top of page

Why Is My Toilet Running? (And How Much Water Is It Wasting?)

Writer: George Campbell
George Campbell
Nov 13
4 min read

Open white toilet in a beige bathroom, with an American Standard logo on the lid and visible water in the bowl.

You’re lying in bed, the house is finally quiet, and then you hear it.


The toilet is running. Again.


A running toilet is one of those problems that’s easy to ignore when a lot of other things are going on. You jiggle the handle, the noise stops, and you go about your day. But here’s the thing: that little hiss could be sending a surprising amount of water (and money) straight down the drain.


So let’s talk about why your toilet keeps running, how much water it may be wasting, and what you can do about it.


First, How Does a Toilet Tank Work?

Don’t worry, we’ll keep this simple!


When you flush, a rubber seal at the bottom of the tank (called the flapper) lifts up and lets water rush into the bowl. Once the tank empties, the flapper drops back down and seals the opening. Then the fill valve refills the tank until a float tells it to shut off.


When everything works the way it should, the whole process takes less than a minute. When one of those parts wears out, water keeps flowing long after the flush is over. That’s likely what you’re hearing when your toilet constantly runs when no one is flushing it.


So what could the causes be?


1. A Worn or Warped Flapper

This is the most common culprit we at G.T. Campbell Plumbing see.


Flappers are made of rubber, and rubber doesn’t last forever. Over time, it can warp, harden, or collect mineral buildup. Once it stops sealing tightly, water slowly leaks from the tank into the bowl. The fill valve then kicks on to top the tank back off, and the cycle repeats.


The tricky part? A flapper leak is often silent. You might only notice your toilet “running” for a few seconds every so often, almost like it’s refilling on its own.


2. The Chain Is Too Long or Too Short

The flapper is connected to the flush handle by a small chain. If that chain is too short, it can hold the flapper slightly open. If it’s too long, it can get tangled or caught underneath the flapper.


Either way, the seal can’t close properly. Good news: this one is usually an easy fix with a simple adjustment.


3. A Faulty Fill Valve

If your toilet makes a constant hissing or gurgling sound, the fill valve may be the problem. This part controls how water enters the tank, and when it wears out, it may not shut off completely.


You might also notice the tank takes longer than usual to refill, or the water level seems off.


4. The Float Is Set Too High

The float tells the fill valve when to stop. If it’s set too high, water keeps rising until it spills into the overflow tube (that open pipe standing up in the middle of the tank). From there, it flows right into the bowl and down the drain. Nonstop.


Lift the tank lid and take a look. If you see water trickling into the overflow tube, the float likely needs to be adjusted.


So, How Much Water Is It Really Wasting?

This is where things get eye-opening.


According to the EPA’s WaterSense program, an old or worn flapper can silently leak thousands of gallons of water a year. The EPA also notes that toilets are often the cause of household leaks that waste up to 180 gallons per week.


And a toilet that’s audibly running nonstop can be even worse. Let’s do some quick math: even a slow trickle of a quarter gallon per minute adds up to 360 gallons a day. That’s more than many households use for everything else combined!


If you’ve recently opened a higher-than-expected water bill, a running toilet is one of the first places we’d tell you to look.


Try the Food Coloring Test

Not sure if your toilet has a silent leak? Here’s an easy way to find out.


  • Remove the tank lid and add a few drops of food coloring to the water in the tank.

  • Don’t flush. Wait about 10 minutes.

  • Check the bowl. If any color has appeared, water is leaking past the flapper.

  • Flush afterward so the coloring doesn’t stain the tank.


It’s quick, it’s easy, and it might save you a lot of money over time!


When to Call a Plumber for Your Toilet Running

Some running toilet fixes, like adjusting a chain or swapping out a flapper, are manageable for a handy homeowner. But if you’ve tried the basics and your toilet is still running, or you’re just not sure what’s going on inside that tank, it’s probably time to call in a professional.


An older toilet with multiple worn parts may also be a good candidate for replacement. Newer, high-efficiency models use far less water per flush than toilets installed decades ago.


Final Thoughts

A running toilet may seem like a minor annoyance, but it can quietly add up to thousands of wasted gallons and a much bigger water bill.


The good news is that most running toilets have simple causes and straightforward fixes. And if you’d rather leave it to the pros, G.T. Campbell Plumbing is here to help. Our team can diagnose the problem, make the repair, and get your bathroom back to proper working order, fast.


Call or text us at (585) 355-1463 to schedule toilet repair anywhere in our Rochester-area service area!

 
 
 

Comments


bottom of page